|
|
Fat Flanders Bagger Bars, 1-1/4 Inch Notched Bars for the Electric Throttle |
|
|
(c) American Side Road Cycles
SmartCart(TM) eCommerce System |
|
 |
Fat Flanders Notched 1-1/4 Handlebars for the Electric Throttle on an Electra Glide
Place Orders Below - Fits Electra Glides, Street Glides, Tri Glides, Ultra Classic and Road Kings, Bagger Handlebars |
- Shipping
to you at our Costs: We
will add shipping costs to your order and charge you only at
our cost (orders
less than $20.00 will be subject to a $2.00 service charge to
offset the handling and billing charges).
- If Shopping
Cart Does Not Work: You may need to turn
off any personal fire wall protection programs. If you are still
having problems using our shopping cart system, please place
your order using our Secure On-line
Order Form.
- E-Mail and
Mailing List Privacy: American Side Road Cycles respects your privacy.
We'll use your e-mail address only when we are confirming your
Internet order, when we answer your questions or notifying you
of changes and updates to the site or other news. We assure you,
we do not make our email list or mailing list available to anyone
for any reason.
- COD Orders: U.S.A. only, no personal checks accepted;
only Money Order or Cashiers Checks. COD orders can be placed
using our Secure
On-line Order Form.
- Be sure to read
our Terms
of Business and Legal
Notice
|
Flanders 1-1/4 inch diameter Wide Ultra Classic Bar with +2 inches more Pullback and +2 inches more Height than stock Bars : Measurements
|
Pullback: |
13" |
|
Height: |
9" |
|
Center: |
12" |
|
Width: |
36.5" |
Diameter: 1-1/4"
These Flanders Handlebars are Notched Bars to work with the Electric Throttle and are 1-1/4" across the center and require the use of 1-1/4" diameter Riser Clamps; with control area at 1" diameter for stock controls |
Flanders 1-1/4 inch diameter Narrow Ultra Classic Bar with +3 inches more Pullback and +2 inches more Height than stock Bars : Measurements
|
Pullback: |
14" |
|
Height: |
9" |
|
Center: |
12" |
|
Width: |
33.5" |
Diameter: 1-1/4"
These Flanders Handlebars are Notched Bars to work with the Electric Throttle and are 1-1/4" across the center and require the use of 1-1/4" diameter Riser Clamps; with control area at 1" diameter for stock controls |
- No PayPal for Handlebars: We
Cannot accept PayPal payments for Handlebars. Please do not use PayPal to pay for your handlebars.
- Shipping
to you at our Costs: We
will add shipping costs to your handlebar order and charge you only at
our cost - usually around $33 ground UPS in the United States (orders less than $20.00 will be subject to a $2.00
service charge to offset the handling and billing charges).
|
|
Part
Number |
Handlebar
Description |
Price |
Qty |
Click Here to Order |
|
Flanders Notched Handelbars for the Electric Throttle - "Fly by Wire" with Flanders Bars
|
|
|
(c) American Side Road Cycles
SmartCart(TM) eCommerce System |
|
Handlebar
Measurements
All measurements are made in normal riding position.
Height or Rise: Total height measured in a level plane.
Pull Back: Vertical lines from the furthest forward to rear in a level plane.
Center Width: Straight flat section before the start of the bends.
Width: Total overall tip to tip width, no grips or bar end weights.
New cables and new brake
lines? When buying new bars, a rough formula
to follow is to measure the increased heigth + 1/2 the increased
pullback that the new bars will give you. This amount will be
very close to how much additional cable and brake line that you
may need. However, the best method is to fit the new bars to
the motorcycle and then make the increased length determinations,
if needed at all.
Additionally, make sure to allow
room for your new bars to clear your gas tank on full lock turn. |
 |
C&C Motorcycle Seats for Harley Davidsons, Honda Fury and Honda VTX - Made in the USA -
|
|
Lots of
Options - Select from various Stitch Patterns, Leather, Vinyl,
Ostrich, Alligator, Stingray, Gel seats, etc... |
|
|
|
|
|
|
